- 2026-10-30
- 2026-08-19
- 2026-08-13
- 2026-07-07
- 2026-06-28
thermal paper coating machine
1. This machine is an off-machine coater with the following structural configuration:
Unwind unit (automatic splicing) — No. 1 modular blade coater — First-stage air-float hot-air dryer (2 sections, 10m total) — S-wrap draw rolls — No. 2 modular rod coater — Second-stage air-float hot-air dryer (3 sections, 12m total) — S-wrap draw rolls — No. 3 modular rod coater — Third-stage air-float hot-air dryer (2 sections, 10m total) — Back-moistening unit (back coating) — Fourth-stage air-float hot-air dryer (1 section, 4m total) — Finishing cylinder group (three chrome-plated cylinders, φ1250mm) — Two cooling rolls — Three-roll calender — Re-reel unit (automatic splicing)
2. Main Technical Parameters:
2.1. Paper Type:
Base paper width: ≤1200 mm
Base paper basis weight: 35–300 g/m²
Base paper moisture content: 5–7%
Web tension: 120–1000 N
Max. unwinding diameter: 1300 mm
Max. rewinding diameter: 1400 mm
2.2. Operating speed: 200 m/min
Design speed: 250 m/min
Balance speed: 400 m/min
2.3. Power supply voltage: 3×380 V / 50 Hz
Control voltage: 24 V
Compressed air pressure: >0.6 MPa
Steam pressure: >0.8 MPa
2.4. Coating properties and coating weight: Water-soluble coating
2.5. Arrangement: As per user requirements
Maximum weight of lifted load: 4 t
Overall dimensions (L x W x H): 60,000 mm x 7,000 mm x 6,500 mm
Rail gauge: 1,800 mm
3. Technical Description of Main Structure and Scope of Supply 3.1.Automatic paper splicing and retracting device 1 set
3.1.1. Main frame 1 unit
3.1.2. Rotating arm assembly 1 set
3.1.3. Paper roll braking and assist mechanism 2 sets
3.1.4. Automatic splicer 1 set (bottom-splicing type)
3.1.5. 3-inch air-expansion shafts 3 pieces
3.1.6. Pneumatic control cabinet 1 unit
3.1.7. Photoelectric positioning system (splicing arm, rotating frame) 1 set
3.1.8. Electric hoist (to be supplied by the user).
3.2. Modular rod coater 3 sets
The modular rod coater offers two coating methods—flexible blade coating and rod coating—and primarily consists of a feed roll, a backing roll, a coating rod with its holder, and a coating pan.
3.2.1. Frame 1 unit × 3
3.2.2. Feed roller 1 piece × 3
3.2.3. Backing roller (for coating rod) 1 piece × 3
3.2.4. Coating rod and rod holder assembly 1 set × 3
3.2.5. Coating pan 1 set × 3
3.2.6. Limit device 2 sets × 3
3.2.7. Roller edge lubrication device 1 set × 3
3.2.8. Scraper device 1 set × 3
3.2.9. Pneumatic control cabinet 1 set × 3
3.3 Back-side wetting unit 1 set
This unit consists of a rubber roller immersed in a water trough that transfers water (or adhesive solution) to a ceramic roller; the ceramic roller then applies the water film (or adhesive film) onto the paper. Both rollers are equipped with independent drives and feature adjustable speeds. The amount of liquid applied can be controlled by adjusting the rotational speeds and the gap between the two rollers.
3.3.1. Frame 1 unit
3.3.2. Impregnation roller 1 pc
3.3.3. Metering roller 1 pc
3.3.4. Paper pressing roller 1 pc
3.3.5. Limiting device 2 sets
3.3.6. Scraping device 1 set
3.3.7. Stainless steel tank 1 pc
3.3.8. Pneumatic control box 1 set
3.4 Hot-air drying system 8 units
2 units of 5m-long hot-air drying ovens after the first coating;
3 units of 4m-long hot-air drying ovens after the second coating;
2 units of 5m-long hot-air drying ovens after the third coating;
1 unit of 4m-long hot-air drying oven after back coating;
Air-float ovens with steam heating and automatic hot-air temperature control.
3.5. Three-roll soft calender 1 unit (before the reel)
Consists of two rubber-covered rolls and one chilled cast iron roll. All three rolls are driven. Hydraulic loading is employed. Linear pressure: 80 kN/m.
3.6. Conditioning Cylinder Group (1 set)
Consists of three chrome-plated cylinders arranged in upper and lower tiers (two in the upper tier, one in the lower tier) and equipped with dryer fabric systems. The three cylinders share a single drive motor via a gear transmission.
3.7 Automatic Paper Splicing and Roll Handling Unit (featuring a horizontal sliding splicer) — 1 set
The automatic paper splicing and roll handling unit consists of a rotary paper roll stand and a splicer. The rotary paper roll stand comprises the main frame, rotating arm assembly, paper roll braking and drive mechanisms, and paper guide rollers. The horizontal sliding splicer consists of a sliding carriage, rubber pressure roller, paper guide roller, cutting knife, braking motor, and compressed-air system. Maximum paper roll diameter: φ1400 mm. Bottom-feed splicing method. The entire frame features automatic lateral alignment correction.
3.8. Support system As per drawings
3.9 Rollers and others As Per drawings
3.10 Main Drive System and Electrical Control
Includes AC variable-frequency motor, gear reducer, coupling, and protective guards.
Design speed: 250 m/min; operating speed: 200 m/min.
Touchscreen operation: a total of three touchscreen control consoles; one operator control station (pendant box) at each coating head (these pendant boxes do not contain touchscreens).
Five tension control points.
Automatic splicing for both unwinding and rewinding.
Automatic protection prevents startup if critical components are not in the proper state or in the event of an operation error; includes an audible alarm and fault message display.
Audible and visual warning signals upon startup.
4. Scope of Supply
4.1. Items provided by the Supplier: The mechanical and electrical equipment listed above, spanning from the reel unwinder to the reel winder (details not explicitly listed are subject to the Supplier's drawings); this includes all paper threading rolls, drive motors, gear reducers, and electrical control systems shown on the general assembly drawing.
4.2. Items not provided by the Supplier:
Stock preparation system, air compressor, water chiller, cables and cable trays, paper threading rope system, moisture and basis weight detection devices
Civil engineering design and construction
Materials required for installation and commissioning
Wiring between switchgear cabinets and control boxes
Power supply and connection
Air piping between the air source and control boxes
Steam source, compressed air source, and water source
Piping and valves between the steam source and drying cylinders
Piping and fittings beyond the inlet and outlet of the heat exchanger
Piping and valves between the water source and the main machine, and condensate discharge piping
Internal machine lighting and wiring
Insulation materials for air ducts; fabrication of fan platforms

